What RIR and RPE actually mean

RIR (reps in reserve) is the number of clean reps you had left when you racked the weight. RIR 0 is failure — you tried and could not complete another rep through a full range of motion without changing form. RIR 2 means you could have done two more.

RPE is the same idea on a ten-point scale, where RPE 10 is failure and every point below it is one rep in reserve. That lifting-specific scale comes from a 2016 paper by Zourdos and colleagues, which set RPE 10 at zero reps left and showed that bar speed tracks the rating closely — which is why it works as a day-to-day way to regulate load.[3]

What the evidence says

Two systematic reviews cover this question from different angles, and they land in the same place.

The evidence at a glance
StudyWhat it coveredWhat it found
2022[1] 15 trials, training to failure vs stopping short No significant difference. Hypertrophy effect size 0.22 (95% CI −0.11 to 0.55); strength effect size −0.09 (95% CI −0.22 to 0.05).
2023[2] 15 studies, how close to failure sets ended A trivial edge to pushing closer to failure (effect size 0.19), with no moderation by load or volume. The authors called it what it is: small.

Read those numbers plainly. The confidence intervals in the first row straddle zero on both outcomes, which is what "no difference" looks like in statistics. The second row found a difference so small that no lifter could feel it, and could not attribute it to anything about how heavy the bar was.

Why failure is expensive

A set to failure does not produce twice the stimulus of a set stopped with two reps left. It produces roughly the same stimulus and a much bigger bill, paid in three places:

The trade in one line: failure buys you a small, uncertain stimulus and sells you the recovery you needed for the next session.

Where failure still earns its place

Calibrating your RIR honestly

In my experience most people are optimistic — and nothing in the training log corrects that faster than being forced to count. A simple check: once a month, take one exercise you know well, load a weight you believe leaves two or three reps, and do as many clean reps as you can. Count what happened. If you beat your estimate by three reps, your "RIR 2" has been RIR 5 all along — and every set you thought was hard has been a warm-up.

How to run it in practice

Notice what is not on the list: a heavy barbell set taken to failure in the middle of the week. That is the one place the research, your joints and your next session all agree about.

How this shows up in your program

The workout builder prints an effort target for every exercise, as RIR, and changes it by block — calibration, progression, intensification, deload, re-test. If a set felt like RIR 0 in a week that says RIR 3, the number on the card is not the problem; the weight is.

What we still don’t know

Almost every trial here is 8–12 weeks with young, healthy adults. Nobody has measured whether training closer to failure matters more for advanced lifters after a decade of training, or whether it changes anything over a year rather than a block. Treat "failure doesn't matter" as a well-supported default, not a law.

References

  1. Grgic J, Schoenfeld BJ, Orazem J, Sabol F. Effects of resistance training performed to repetition failure or non-failure on muscular strength and hypertrophy: a systematic review and meta-analysis. J Sport Health Sci. 2022;11(2):202–211. PubMed 33497853
  2. Refalo MC, Helms ER, Trexler ET, Hamilton DL, Fyfe JJ. Influence of resistance training proximity-to-failure on skeletal muscle hypertrophy: a systematic review with meta-analysis. Sports Med. 2023;53(3):649–665. PubMed 36334240
  3. Zourdos MC, Klemp A, Dolan C, et al. Novel resistance training-specific rating of perceived exertion scale measuring repetitions in reserve. J Strength Cond Res. 2016;30(1):267–275. PubMed 26049792

Related reading

Want this applied to your own training? Bring your current week and I will count it with you and rebuild it around what you actually want to grow.

Work with me 1:1